Yellow | Q/A about roadways computers

All roadway guys. lets try to help with the computers on the forklifts for our fellow yellow brothers so this transaction woks. do or die or the unemployment line.

Thank you , we are YRC and we need this to work

snake eyes said:

All roadway guys. lets try to help with the computers on the forklifts for our fellow yellow brothers so this transaction woks. do or die or the unemployment line.

Click to expand...

Well the thought was nice, but the software has been changed so nobody knows what to do. Keep your cheat sheets on hand. Would have been nice to make this change in the middle of the month instead of the 1st of the month.

Just remember F3 is your friend. Always check your door numbers on your computer to make sure it is correct. Stacking you will have to enter door number every bill. They are not that hard to figure out. The road drivers that became utility drivers where even able to figure it out in a couple of weeks.

Thank you to all the former Rdwy guys, any help is appreciated. We all need this to work as snake eyes stated, we don't need the unemployment line.

Fork Lifts

Here's a little help for the Dock People .First you must log on ! When a trailer comes up to a door you must PLUG the door first that's F-2 on your fork lift screen after inputting the door number and trailer number you hit SPACE . Next you must either open a stack or strip that's F-1 you input the door number again and the trailer number after that your ready to go to work !! When moving freight from one door to another your most important key is F-3 this will let you stack and strip freight from open trailers !! Hit F-3 than 1 for strip and 3 for stack !!! Any time you not sure about what a trailer in a door is for hit F-6 and then input the door number at the bottom of the screen it will tell you the destination, weight and bill count .Don't forget to "SCAN" every bill as you load it or unload it if not you might go to lunch and the door could be closed and OPPS where did the freight go to !! Hopes this very small lesson helps someone out !

what happened to 102 and 119!!!!!!!

ADC instuctions

WIRELESS ADC GUIDE

Inbound/Outbound Stripping and Stacking Open a Stack Open a Strip
Press <F1> to open the Main Menu Press <F1> to open the Main Menu
Press <1> to open the Stack Trailer Menu Press <2> to open the Strip Trailer Menu
Press <1> to Open Stack Press <1> to Open Strip
Type the door number and press <Enter> Type the door number and press <Enter>
Type the trailer number and press <Enter> Type the trailer number and press <Enter>
Type the Manifest Destination and press <Enter>

Stack a PRO Strip a PRO
Press <F3> to open the Pro Menu Press <F3> to open the Pro Menu
Press <3> to Stack Pros Press <1> to Strip Pros
Type the Door number and press <Enter> Type the Door number and press <Enter>
Scan the barcode Scan the barcode
Verify the Handling Units number is correct and press <Enter> At the lower left where to take the freight is displayed
- If incorrect type the number of handling units and press <Enter> Verify the Handling Units number is correct and press <Enter>
Verify the Weight is correct and press <Enter> - If incorrect type the number of handling units and press <Enter>
- If incorrect type the weight and press <Enter> Verify the Weight is correct and press <Enter>
If there are no damages press <N> - If incorrect type the weight and press <Enter>
-If there are damages type in appropriate letter and press <Enter> If there are no damages press <N>
Type the percent full for % Capacity and press <Enter> -If there are damages type in appropriate letter and press <Enter>

Temp Close a Stack Temp Close a Strip
Press <F1> to open the Main Menu Press <F1> to open the Main Menu
Press <1> to open the Stack Trailer Menu Press <2> to open the Strip Trailer Menu
Press <4> to Temp Close Press <3> to Temp Close
Type the door number and press <Enter> Type the door number and press <Enter>
Type the percent full for % Capacity and press <Enter> Type the percent full for % Capacity and press <Enter>

Close a Stack Close a Strip
Press <F1> to open the Main Menu Press <F1> to open the Main Menu
Press <1> to open the Stack Trailer Menu Press <2> to open the Strip Trailer Menu
Press <2> to Close Stack Press <2> to Close Stack
Type the Door number and press <Enter> Type the Door number and press <Enter>
Type the Door capacity and press <Enter> Type <Y> and press <Enter>
Type the Seal number and press <Enter>
Type in comments (if any), and press <Enter> twice

What a great effort put forth there Rex, nice job! Okay everyone copy & paste and print!!
But I am curious to know how long it took you to type that all out? Hopefully your not a hunt and peck typist??:smilie_132:

nice job rex309! i'm going from a roadway barn to a yellow barn are the waybills going to look like the roadway waybill or the yellow bill?